Comprehensive Guide kuShanghai Mitsubishi Elevator Electrical Board Settings
Zviri Mukati
1. Kudzora Cabinet (Item 203) Zvirongwa
1.1 P1 Bhodhi Configuration (Mienzaniso: P203758B000/P203768B000)
1.1 Operating Mode Configuration
| Basa reNyika | MON0 | MON1 | SET0 | SET1 |
|---|---|---|---|---|
| Normal Operation | 8 | 0 | 8 | 0 |
| Debug/Sevhisi | Tevera debugging manual |
1.2 Kugadzirisa Kukurukurirana (Jumper Mitemo)
| Elevator Type | GCTL | GCTH | ELE.NO (Group Control) |
|---|---|---|---|
| Single Elevator | Kwete kusvetuka | Kwete kusvetuka | - |
| Parallel/Boka | ● (Akasvetuka) | ● (Akasvetuka) | 1~4 (ye#F~#I maelevator) |
2. Mota Yepamusoro Station (Item 231) Zvirongwa
2.1 Door Control Board (Muenzaniso: P231709B000)
2.2 Basic Jumper Settings
| Function | Jumper | Configuration Rule |
|---|---|---|
| OLT Signal Disable | JOLT | Jumper kana chete CLT/OLT yakaiswa |
| Mberi/Kumashure Musuo | FRDR | Jumper yemagonhi ekumashure |
| Motor Type Selection | MU | Jumper yeasynchronous motors (IM) |
2.3 Mota Direction & Parameters
| By Mota Model | Motor Type | FB Jumper |
|---|---|---|
| LV1-2SR/LV2-2SR | Asynchronous | ● |
| LV1-2SL | Synchronous | ● |
2.4 SP01-03 Jumper Mabasa
| Jumper Group | Function | Configuration Rule |
|---|---|---|
| SP01-0,1 | Kudzora Mode | Set pagonhi mota modhi |
| SP01-2,3 | DLD Sensitivity | ● ● (Standard) / ●○ (Yakaderera) |
| SP01-4,5 | JJ Size | Tevera chibvumirano parameters |
| SP02-6 | Mota Type (PM chete) | Jumper kana TYP=0 |
2.5 Jumper marongero eJP1~JP5
| JP1 | JP2 | JP3 | JP4 | JP5 | |
| 1D1G | 1-2 | 1-2 | X | X | 1-2 |
| 1D2G/2D2G | X | X | 2-3 | 2-3 | 1-2 |
Cherechedza: "1-2" zvinoreva jumper pini 1 uye 2; “2-3” zvinoreva anosvetuka mapini 2 ne3
3. Mota Inoshanda Panel (Item 235) Zvirongwa
3.1 Bhatani Bhodhi (Muenzaniso: P235711B000)
3.2 Bhatani Magadzirirwo Magadzirirwo
| Rongedzo Type | Button Count | RSW0 Setting | RSW1 Setting |
|---|---|---|---|
| Vertical | 2-16 | 2-F | 0-1 |
| 17-32 | 1-0 | 1-2 | |
| Horizontal | 2-32 | 0-F | 0 |
3.3 Jumper Configurations (J7/J11)
| Panel Type | J7.1 | J7.2 | J7.4 | J11.1 | J11.2 | J11.4 |
|---|---|---|---|---|---|---|
| Front Main Panel | ● | ● | - | ● | ● | - |
| Rear Main Panel | ● | - | ● | ● | - | ● |
4. Kudzika Station (Item 280) Zvirongwa
4.1 Kumisikidza Bhodhi (Muenzaniso: P280704B000)
4.2 Jumper Settings
| Floor Position | TERH | TERL |
|---|---|---|
| Pasi Pasi (Hapana Chiratidziro) | ● | ● |
| Pakati/Pamusoro Floors | - | - |
4.3 Floor Bhatani Encoding (SW1/SW2)
| Bhatani Nhamba | SW1 | SW2 | Bhatani Nhamba | SW1 | SW2 |
|---|---|---|---|---|---|
| 1-16 | 1-F | 0 | 33-48 | 1-F | 0-2 |
| 17-32 | 1-F | 1 | 49-64 | 1-F | 1-2 |
5. Kusvika Kufona (Item 366) Zvirongwa
5.1 Kunze Kufona Board (Mienzaniso: P366714B000/P366718B000)
5.2 Jumper Mitemo
| Function | Jumper | Configuration Rule |
|---|---|---|
| Pazasi Floor Comms | YAMBIRO/KUGONA | Nguva dzose yakasvetuka |
| Floor Setup | SET/J3 | Jumper kwenguva pfupi panguva yekuseta |
| Rear Door Config | J2 | Jumper yemagonhi ekumashure |
6. Manotsi Akakosha
6.1 Operational Guidelines
-
Chengetedzo Kutanga: Nguva dzose bvisa simba usati wagadzirisa jumper. Shandisa CAT III 1000V insulated maturusi.
-
Version Control: Reveridate marongero mushure mekusimudzira sisitimu uchishandisa yazvino bhuku (Nyamavhuvhu 2023).
-
Troubleshooting: Nekukanganisa makodhi "F1" kana "E2", tungamira kutarisa yakasununguka kana misconfigured jumpers.
6.2 Yakarongwa Data Suggestion
Technical Support: Shanyirawww.felevator.comzvekuvandudza kana kubata mainjiniya ane certified.
Mifananidzo Inonyorwa:
-
Kudzora Cabinet P1 Board: Simbisa GCTL/GCTH zvinzvimbo, ELE.NO zone, uye MON/SET inotenderera switch.
-
Door Kudzora SP Jumpers: Ruvara-code senitivity uye mota mhando nzvimbo.
-
Mota Bhatani Bhodhi: Nyora zvakajeka J7 / J11 jumpers uye mabhatani marongero modes.
-
Landing Board: TERH/TERL zvinzvimbo uye SW1/SW2 pasi encoding.
-
Landing Call Board: CANH/CANL kurukurirano jumpers uye pasi setup nzvimbo.