I-Shanghai Mitsubishi LEHY-Pro (NV5X1) I-Elevator ye-Low-Speed Operation Debugging Essentials
1.Ukulungiselela phambi kokusebenza kwesantya esiphantsi
①. Ukuba kukho isixhobo sonikezelo lombane olugcinwayo olungxamisekileyo, ukufakwa kweengcingo ngesandla kuyafuneka ukuze kugcinwe isilathisi sombane esiqhelekileyo #NOR kurhulumente.
Ixesha elifutshane lee-terminals ze-420 (ZTNO-01) kunye ne-NORR (ZTNO-02) kwibhodi ye-Z1.
②. Jika i-toggle switch "DRSW/IND" kwisixhobo sokusebenzisana somntu ukuya kwindawo ephakathi ukukhulula imo yokusikwa kocango kumanyathelo angaphambili.
③. Xa isiphaluka sokhuseleko siqhelekile, i-LED ehambelanayo kwisixhobo sokusebenzisana nomntu kufuneka sikhanyise. Ukuba kukho nakuphi na ukutshintshwa kweesekethe zokhuseleko kunqanyuliwe, i-LED 29 kufuneka icinywe.
(1) Baleka/Yeka iswitshi kwibhokisi yokulawula igumbi lomatshini;
(2) I-Run/Stop switch kwibhokisi yokulawula isikhululo esiphezulu semoto;
(3) Baleka/Yeka iswitshi kwibhokisi yokusebenza emhadini;
(4) Isitshixo sokumisa igumbi lomatshini (ukuba kukho);
(5) Isitshixo sokuphuma kwinqwelo-mafutha phezulu (ukuba sikhona);
(6) Ukutshintshela i-clamp yokhuseleko lwemoto (inokuba yi-short-circuited ekusebenzeni kombane kaxakeka);
(7) Isitshixo sokuphuma ngexesha likaxakeka (ukuba sikhona);
(8) Isitshixo socango lomngxuma (ukuba sikhona);
(9) Isitshixo sokumisa umngxuma (kuquka isixhobo sokumisa umngxuma wesibini (ukuba sikhona));
(10) Umyinge wesantya semoto ecaleni kwesantya sokutshintsha isithinteli (sinokuba siseko esifutshane kumsebenzi ongxamisekileyo wombane);
11
12
13
(14) Isitshixo somda wesiphelo se-TER.SW (sinokuba sifutshane-kwi-circuit kwimeko yokusebenza kombane kaxakeka);
15
(16) Iswitshi yombane yesithinteli sesantya kwicala elichasene nobunzima (ukuba bukho) (unokuba mfutshane xa kunokusebenza umbane ongxamisekileyo);
(17) Isixhobo sokuguqula ngesandla (ukuba sikhona);
(18) Ukutshixa umnyango wecala (olungiselelwe i-ADK);
(19) Isixhobo sokuphuma ngexesha likaxakeka kwisikhululo esisemgangathweni (ukuba sikhona);
(20) Ukutshintsha ileli emhadini (ukuba kukho);
(21) Ukubuyekeza isitshixo sevili (ukuba sikhona);
22
(23) Intambo yocingo ethambileyo kunye nokutshintsha intambo eyaphukileyo (elungiselelwe ulwalathiso lwaseRashiya).
④. Xa amaqhosha okuqhuba kunye naphezulu / ezantsi esixhobo sokusebenza kombane esingxamisekileyo ecinezelwe ngaxeshanye kwaye ngokuqhubekayo, ezi diode zilandelayo ezikhupha ukukhanya kunye nabafowunelwa kufuneka basebenze ngokulandelelana.
Ukuba iqhosha eliPhezulu / ezantsi licofa ngokuqhubekayo, i-LED kunye noqhagamshelwano uya kuphuma okanye akhulule, kwaye uphinde uphinde ulandelelwano olungentla amaxesha ama-3. Oku kungenxa yokuba i-motor ayixhunyiwe kwaye i-TGBL (isantya esiphantsi kakhulu) ibangelwa impazamo.
⑤. Vala abaphuli beesekethe iMCB kunye neCP.
⑥. Phinda uqhagamshele iintambo zemoto ebezifudula zisusiwe u-U, V, W kunye neentambo zeekhoyili zebrake ngokwendlela yocingo lokuqala.
Ukuba i-brake cable connector ayixhunyiwe kwikhabhinethi yokulawula, inkqubo yokusebenza ayiyi kuqala.
⑦. Ukusebenza ngesantya esisezantsi kunokusebenza kwigumbi lomatshini usebenzisa iswitshi kwisixhobo sokusebenza kombane esingxamisekileyo. Emva kokujonga i-encoder wiring, kufuneka kwakhona ujonge iswitshi yokusebenza kumphezulu wemoto.
2.Bhalela kwipali yemagnethi
La manyathelo alandelayo angenziwa kuphela emva kokuqinisekisa ukuba iingcango zomgangatho kunye neengcango zemoto zivaliwe ngokukhuselekileyo.
| Itheyibhile 1 Amanyathelo okubhala epali yemagnethi | |||
| Inombolo yesiriyeli | Amanyathelo okulungisa | Ukulumkela | |
| 1 | Qinisekisa ukuba ii-motor cables U, V, W kunye nee-brake cables zixhunyiwe ngokufanelekileyo kwikhabhinethi yokulawula. | ||
| 2 | Qinisekisa ukuba i-CP breaker yesiphaluka ngaphakathi kwikhabhinethi yokulawula ivaliwe. | ||
| 3 | Qinisekisa ukuba ilifti iyahlangabezana nemiqathango yokusebenza ngesantya esisezantsi. Qinisekisa ukuba (EYOKUQHELEKILEYO/EXAMISEKILEYO) iswitsha yesixhobo sokusebenza kombane esingxamisekileyo sijikelwe kwicala le (EMERGENCY). | ||
| 4 | Cwangcisa i-rotary switch SET1/0 kwisixhobo sojongano lomatshini womntu ukuya kwi-0/D, kwaye ikhowudi yamacandelo asixhenxe iya kukhanya ukubonisa i-A0D. |
| |
| 5 | Cinezela iswitshi ye-SW1 kwi-interface yomatshini womntu ukuya ezantsi kube kanye, ikhowudi yamacandelo asixhenxe iya kudanyaza ngokukhawuleza, kwaye indawo yangoku yesibonda semagnethi iya kuboniswa. | Cofa u-SW1 okokuqala | |
| 6 | Cinezela iswitshi ye-SW1 kwisixhobo sojongano lomatshini womntu phantsi kwakhona (ubuncinci imizuzwana eyi-1.5) de ikhowudi yamacandelo asixhenxe ibonise i-PXX (i-XX ngumaleko wongqamaniso lwangoku. Ukuba umaleko awubhalwanga, umaleko wongqamaniso obonisiweyo unokungachanekanga). | Cofa u-SW1 okwesibini | |
| 7 | Ukusebenza kombane ongxamisekileyo, de kube ikhowudi yamacandelo asixhenxe ibonisa indawo entsha ye-pole magnetic, kwaye i-elevator ayimisi ngokukhawuleza, indawo ye-pole magnetic ibhalwe ngempumelelo. | Nceda uqaphele ukuba ixabiso lendawo yepoli yemagnethi liyatshintsha njengesiseko sokubhala ngempumelelo. | |
| 8 | Cwangcisa iswitshi ejikelezayo SET1/0 kwisixhobo sokusebenzisana somntu ukuya ku-0/8, kwaye ucinezele kwaye ubambe i-SW1 switch phantsi de ikhowudi yamacandelo asixhenxe iqale ukukhanyisa ngokukhawuleza, kwaye uphume kwimo ye-SET. | ||
3. Ukusebenza kwesantya esiphantsi
Xa uxhotyiswe ngenkqubo yolwazi lwe-shaft, i-sensor yendawo epheleleyo inezilungiso ezimbini, ezizezi: isikali samagnetic kunye ne-code tape. Ukuze kube lula, umlinganiselo wamagnetic kunye nekhowudi ye-tape zibizwa ngokudibeneyo njengezikali kwisicatshulwa esilandelayo.
Phambi kokuba isikali sifakwe, faka imowudi yokufaka isikali kuqala, jonga u-5.
Emva kokucinezela umbane ongxamisekileyo okanye ulungiso oluya phezulu kunye neqhosha lomyalelo, i-LED UP kwisixhobo sokusebenzisana nomntu kufuneka sikhanyise kwaye imoto kufuneka inyuke. Emva kokucinezela iqhosha elisezantsi kunye neqhosha lomyalelo, i-LED DN kwisixhobo sokusebenzisana nomntu kufuneka sikhanyise kwaye imoto kufuneka yehle. Ukuba imoto ilula kune-counterweight, imoto ingaba neempembelelo eziphezulu kwaye ihle ngokuqhelekileyo. Isantya somsebenzi wezandla yi-15m/min.
Ngexesha lokulungiswa komsebenzi owenziwe ngesandla, kufuneka kuqinisekiswe ukuba i-brake inokuvulwa ngokupheleleyo kwaye umatshini wokutsala awunayo ingxolo engaqhelekanga kunye nokungcangcazela.
Ukongeza, xa imoto iyeka, abafowunelwa be-brake kufuneka bavalwe ngokupheleleyo ukuze kuqinisekiswe ukusebenza kakuhle kwebhuleki.
Ngethuba lokusebenza ngesandla, imoto kufuneka ime ngokukhawuleza xa isiphaluka sokhuseleko esifana nokutshintshwa kokhuseleko, umnyango womgangatho okanye ifowuni yokuvala umnyango wemoto unqanyuliwe.
Ngethuba lonke lofakelo kunye nenkqubo yokulungelelanisa, ukwenzela ukukhusela i-motor ekutshiseni ngenxa yokugqithisa, la manqaku alandelayo kufuneka aphathwe ngononophelo olukhulu.
I. Itsheyini yembuyekezo kufuneka ixhonywe phambi kokuba kwenziwe umsebenzi onesantya esiphantsi.
Ukuba ikhonkco lembuyekezo alixhonywanga ngexesha lokusebenza kwesantya esisezantsi, i-motor iya kusebenza phantsi komqathango wokudlula umbane olinganisiweyo. Ngoko ke, ukuba akukho mfuneko ekhethekileyo, le meko ingentla kufuneka igwenywe. Ukuba kuyimfuneko ukusebenza ngesantya esiphantsi ngaphandle kokuxhoma ikhonkco lembuyekezo, kuyimfuneko ukongeza umthwalo ofanelekileyo kwimoto ukulinganisela ubunzima be-counterweight. Ukuba i-stroke idlula i-100 yeemitha, kuyimfuneko ukubeka iliso kwi-motor current ukuze kuqinisekiswe ukuba i-current ayidluli amaxesha angama-1.5 ngokulinganiselwe.
Ukuba i-motor current idlula amaxesha angama-1.5 ixabiso elilinganisiweyo, i-motor iya kutshisa ngaphakathi kwemizuzu embalwa.
II. Amanyathelo okuxhoma kunye neemfuno zekhonkco lembuyekezo kufuneka zibhekiselele kwindawo yomatshini yolwazi lofakelo kunye nokugcinwa.
III. Emva kokuba ikhonkco lembuyekezo lixhonyiwe, imoto kufuneka ilayishwe ngomthwalo we-balance counterweight kwaye iqhube ngesantya esiphantsi kuze kube yilapho i-balance coefficient ivavanywa.
Qaphela: Ukuba inkqubo yokufakela i-scaffolding-free yofakelo yamkelwe, kuyimfuneko ukusebenzisa izixhobo ezikhethekileyo ze-scaffolding-free kwaye ufake imowudi yokufakela i-scaffolding-free ukuhambisa imoto.
4. Ukufunda phantsi ngePAD
Xa uxhotyiswe nge-PAD, umsebenzi wokubhala umaleko we-manual unokwenziwa kuphela emva kokuba kufakwe i-terminal deceleration switch, ipleyiti yokuhlukanisa imagnethi, ukulinganisa kunye nokutshintsha kwakhona ukulinganisa equleni kufakwe.
Xa uxhotyiswe ngenkqubo yolwazi kakuhle, akukho msebenzi unjalo.
| Uluhlu 2 Amanyathelo okufunda kuMgangatho xa uxhotyiswe ngePAD | ||
| Inombolo yesiriyeli | Amanyathelo okulungisa | Ukulumkela |
| 1 | Ukusebenza kombane okungxamisekileyo kumisa imoto kumgangatho wetheminali osezantsi wokulinganisa kwakhona indawo. | |
| 2 | Lungisa i-rotary switch SET1 kwisixhobo sojongano lomatshini womntu ukuya kwi-0 kunye ne-SET0 ukuya kwi-7, kwaye ikhowudi yamacandelo asixhenxe iya kukhanya kwaye ibonise i-A07. | SET1/0=0/7
|
| 3 | Cinezela kwaye ubambe iswitshi ye-SW1 kwisixhobo sojongano lomatshini womntu de ikhowudi yamacandelo asixhenxe iqale ukukhanyisa ngokukhawuleza, kwaye emva koko i-F01 iya kuboniswa. | Cofa u-SW1 okokuqala
|
| 4 | Cinezela kwaye ubambe iswitshi ye-SW1 kwisixhobo sojongano lomatshini womntu phantsi kwakhona de ikhowudi yamacandelo asixhenxe iqalise ukudanyaza, kwaye ke F00 iya kuboniswa. | Cofa u-SW1 okwesibini
|
| 5 | Baleka imoto ngesandla ngokuqhubekayo ukusuka kumgangatho osezantsi wetheminali ukuya kumgangatho ophezulu wetheminali emva koko ukuya kwindawo yokulinganisa. | |
| 6 | I-elevator iya kuyeka ngokuzenzekelayo ukusebenza kwaye ikhowudi yamacandelo asixhenxe iya kuyeka ukukhanya, ebonisa ukuba ukubhala phantsi kuphumelele. | |
| 7 | Ukuba imoto iyama ngaphambi kokuba ifike kumgangatho ophezulu, phinda amanyathelo (1)-(5). | Ukuba idatha yobude bomgangatho ayinakubhalwa, jonga indawo yesenzo sokutshintsha komda wesiphelo, isixhobo sokulinganisa/ukulinganisa kwakhona kunye ne-encoder. |
| 8 | Buyisela i-rotary switches SET1 kunye ne-SET0 kwisixhobo sokusebenzisana nomntu kumatshini kwi-0 kunye ne-8 ngokulandelanayo. | SET1/0=0/8 |
| 9 | Cinezela kwaye ubambe iswitshi ye-SW1 kwisixhobo sojongano lomatshini womntu de ikhowudi yamacandelo asixhenxe iqalise ukudanyaza ngokukhawuleza ukuphuma kwimo ye-SET. | |
5. Ukufunda phantsi xa ulungisa inkqubo yolwazi lwe-shaft
5.1 Ukufakela isikali
Xa uxhotyiswe ngenkqubo yolwazi lwe-shaft, le modi ingangenwa kuphela xa usenza imisebenzi yofakelo lwesikali kunye nokufunda kwesimo somda wethutyana. Akuvumelekanga ukungena kule modi kwezinye iimeko!
Emva kokuba isikali sifakwe, indawo yokukhawulela yesikhashana ibhalwa ngokukhawuleza.
Xa uxhotyiswe nge-PAD, akukho msebenzi onjalo.
| IThebhile 3 Ukungena kunye nokuphuma kofakelo lwesikali | ||
| Inombolo yesiriyeli | Amanyathelo okulungisa | Ukulumkela |
| 1 | Qinisekisa ukuba ilifti ikwimo engxamisekileyo okanye imo yokuhlola. | |
| 2 | Lungisa i-rotary switch SET1 kwisixhobo sojongano lomntu ukuya kwi-2 kunye ne-SET0 ukuya ku-A, kwaye ikhowudi yamacandelo asixhenxe iya kukhanya kwaye ibonise i-A2A. | SET1/0=2/A
|
| 3 | Cinezela i-SW1 iswitshi kwisixhobo sojongano lomatshini womntu ezantsi kanye, kwaye ikhowudi yamacandelo asixhenxe iya kudanyaza ngokukhawuleza, kwaye ke iya kubonisa "cima" ngaphandle kokudanyaza. | Cofa u-SW1 okokuqala
|
| 4 | Cinezela kwaye ubambe iswitshi ye-SW1 kwisixhobo sojongano lomatshini womntu phantsi (ubuncinci imizuzwana eyi-1.5) ide ikhowudi yamacandelo asixhenxe iqalise ukudanyaza kancinane. | Cofa u-SW1 okwesibini |
| 5 | Jika i-RESET switch ye-ZFS-ELE200 ngaphakathi kwe-10s (ivumelekile ukubamba ixesha le- [0.5s, 10s]). | Vula ukuseta ngokutsha kwi-ZFS-ELE200 |
| 6 | Ikhowudi yamacandelo asixhenxe iya kubonisa "kwi", kwaye imodi yokufaka isikali ifakwe ngempumelelo. |  |
| 7 | Ukuba ikhowudi yamacandelo asixhenxe ibonisa "kwi", kufuneka ujikeleze i-RESET switch ye-ZFS-ELE200 kwakhona ukucima iimpazamo ezinxulumene ne-ZFS-ELE200, kwaye ikhowudi yamacandelo asixhenxe iya kubonisa "kwi". | Ukuba ityhubhu yedijithali ayibonisi ".", kufuneka ujikeleze ukuseta ngokutsha kwakhona. |
| 8 | Yenza ufakelo lwesikali. Xa umbane ongxamisekileyo okanye umsebenzi wolondolozo lwenziwa kwimodi yokufaka isikali, i-buzzer ephezulu yemoto iya kuvakala. |
|
| 9 | Emva kokuba ufakelo lwerula lugqityiwe, cofa kwaye ubambe iswitshi ye-SW1 kwisixhobo sojongano lomatshini womntu (ubuncinci imizuzwana eyi-1.5) de ikhowudi enamacandelo asixhenxe ibonakale OFF ukuphuma kwimowudi yofako lwerula. | |
Phawula:
①. Ukongeza kule misebenzi ingentla, ukuguqula i-SET1/0 ukutshintshela kude ne-2/A okanye ukusetha kwakhona ibhodi ye-P1 kuya kuphuma ngokuzenzekelayo kwimodi yokufaka isikali;
②. Intsingiselo yekhowudi yamacandelo asixhenxe eboniswe xa ungena kwaye uphuma kwimowudi yokufaka isikali iboniswe kwitheyibhile elandelayo:
| Uluhlu lwesi-4 Intsingiselo yekhowudi yamacandelo asixhenxe | |
| Umboniso wamacandelo asixhenxe | Intsingiselo |
| kwi | I-elevator ingene kwimowudi yokufaka isikali kwaye idinga ukucima iimpazamo ezinxulumene ne-ZFS-ELE200. |
| kwi | I-elevator ingene kwindlela yokufaka isikali |
| icimile | I-elevator iphumile kwindlela yofakelo lwesikali |
| E1 | Ixesha liphelile xa ungena okanye uphuma kwimowudi yofakelo lwerula |
| E2 | I-RESET iswitshi ayisebenzi kwimizuzwana eyi-10 xa ingena kwindlela yokufaka isikali. |
| E3 | ngaphandle kolwazi lwe-SDO |
5.2 Ukubhalwa komlinganiselo wexeshana
Xa inkqubo yolwazi lwe-shaft ixhotyiswe, ukuba indawo yokukhawulela yesikhashana ayibhalwanga, i-elevator kufuneka ibe kwimodi yokulondoloza ngaphambi kokungena kwimodi yokufaka isikali. Musa ukucima umbane ngelixa ubhala indawo yomda wexeshana ophezulu/ophantsi.
Emva kokuba indawo engaphezulu/esezantsi yomda wexeshana ibhaliwe, ilifti iya kuba nomsebenzi wokhuseleko lwesiphelo. Xa umsebenzi ongxamisekileyo wombane okanye wolondolozo ufika kwindawo yocango lomgangatho wetheminali, ilifti mayiyeke ukusebenza ngokuqhelekileyo.
Xa uxhotyiswe ngePAD, akukho msebenzi onjalo.
| Itheyibhile 5 Umlinganiselo wexeshana amanyathelo okubhala | ||
| Inombolo yesiriyeli | Amanyathelo okulungisa | Ukulumkela |
| 1 | Umqhubi wemoto ophezulu uqhuba imoto ye-elevator ukuya kwindawo ephezulu yesigxina sexeshana (isenzo se-UOT) ngokulungiswa. | Qinisekisa indawo yofakelo lokutshintsha ngokomzobo wofakelo |
| 2 | Umsebenzisi kwigumbi lekhompyutha ulungelelanisa i-rotary switch SET1 kwisixhobo sokusebenzisana somntu ukuya kwi-5 kunye ne-SET0 ukuya kwi-2, kwaye ikhowudi yamacandelo asixhenxe iya kukhanya ukubonisa i-A52. | SET1/0=5/2
|
| 3 | Cinezela iswitshi ye-SW1 kwisixhobo sojongano lomatshini womntu ezantsi kanye, ikhowudi yamacandelo asixhenxe iya kudanyaza ngokukhawuleza, kwaye emva koko iya kudanyaza kancinane ukubonisa indawo yomda wexeshana ophezulu kwipharamitha yangoku. | Cofa u-SW1 okokuqala |
| 4 | Cinezela kwaye ubambe iswitshi ye-SW1 kwisixhobo sokusebenzisana nomntu phantsi (ubuncinci imizuzwana eyi-1.5) de ikhowudi yamacandelo asixhenxe iqalise ukudanyaza ngokukhawuleza. Emva kokugqitywa kokubhalwa, ikhowudi yamacandelo asixhenxe iya kuyeka ukukhanya kwaye ibonise indawo ephezulu yesigxina somda kwipharamitha. Ukuba ukubhala kusilele, u-E uya kuboniswa. | Cofa u-SW1 okwesibini |
| 5 | Umsebenzisi ophezu kwemoto ubuyisela ukutshintshela ukugcinwa kwimeko yesiqhelo, kwaye umqhubi kwigumbi lomatshini wenza umsebenzi ongxamisekileyo wombane ukuhambisa i-elevator phantsi kwaye iphume kwindawo ephezulu yesigxina somda (UOT). | Ifuna ukusebenza ngabasebenzi kwigumbi lomatshini |
| 6 | Jika i-ZFS-ELE200's RESET switch ukucima iimpazamo ezinxulumene ne-ZFS-ELE200. | |
| 7 | Umsebenzisi kumphezulu wemoto uqhuba imoto yelifti ukuya kwindawo esezantsi yomda wexeshana (isenzo seDOT) ngokulungiswa. | |
| 8 | Umsebenzisi kwigumbi lekhompyutha ulungelelanisa i-rotary switch SET1 kwisixhobo sokusebenzisana somntu ukuya kwi-5 kunye ne-SET0 ukuya kwi-1, kwaye ikhowudi yamacandelo asixhenxe iya kukhanya ukubonisa i-A51. | SET1/0=5/1 |
| 9 | Cinezela i-SW1 iswitsha kwisixhobo sojongano lomatshini womntu ezantsi kanye, ikhowudi yamacandelo asixhenxe iya kudanyaza ngokukhawuleza, kwaye emva koko iya kudanyaza kancinane ukubonisa indawo esezantsi yomda wexeshana kwipharamitha yangoku. | Cofa u-SW1 okokuqala |
| 10 | Cinezela kwaye ubambe iswitshi ye-SW1 kwisixhobo sokusebenzisana nomntu phantsi (ubuncinci imizuzwana eyi-1.5) de ikhowudi yamacandelo asixhenxe iqalise ukudanyaza ngokukhawuleza. Emva kokugqitywa kokubhalwa, ikhowudi yamacandelo asixhenxe iya kuyeka ukudanyaza kwaye ibonise indawo ephantsi yesigxina somda kwipharamitha. Ukuba ukubhala kusilele, u-E uya kuboniswa. | Cofa u-SW1 okwesibini |
| 11 | Umsebenzisi ophezu kwemoto ubuyisela utshintsho lokuhlola kwindawo yesiqhelo, kwaye umsebenzi okwigumbi lomatshini wenza umsebenzi ongxamisekileyo wombane ukuhambisa ilifti inyuke iphume kwindawo esezantsi yomda wethutyana (DOT). | Ifuna ukusebenza ngabasebenzi kwigumbi lomatshini |
| 12 | Seta kwakhona ibhodi ye-P1 okanye ucime i-elevator uze uyivule kwakhona. | Ungaphoswa yiyo! |
5.3 Bhala idatha yomgangatho
Umsebenzi wokubhala unokwenziwa kuphela emva kokuba i-ZFS-ELE200 ifakwe, ukukhanya kwesalathisi kwibhokisi yokhuseleko kuqhelekileyo, ukufundwa kwexesha lomda wexeshana kugqityiwe, iimpawu zomnyango we-elevator ziqhelekileyo (kuquka i-GS, DS, CLT, OLT, FG2, MBS, njl. isixhobo sokuthintela sisebenza ngokufanelekileyo.
Xa usenza imisebenzi yokubhala umaleko, kuyacetyiswa ukuba umntu ahlale kwigumbi lomatshini ukuze ahlangule xa kuvela imeko!
Iileya zokubhala ezizenzekelayo ziyakhethwa.
| Uluhlu lwesi-6 Amanyathelo okubhala ngokuzenzekelayo idatha yomaleko | ||
| Inombolo yesiriyeli | Amanyathelo okulungisa | Ukulumkela |
| 1 | Misa i-elevator kumgangatho ophantsi okanye kwindawo yomnyango ophezulu kwaye utshintshe i-elevator kwimodi ezenzekelayo. | Ngeli xesha, ekubeni i-ZFS-ELE200 iswele isignali yendawo, i-29 # ukukhanya ayikwazi ukukhanyiswa, okuqhelekileyo. |
| 2 | Cwangcisa i-SET1/0 ukuya ku-5/3 (ukufunda ukusuka ezantsi ukuya phezulu) okanye i-5/4 (ukufunda ukusuka phezulu ukuya ezantsi), cinezela u-SW1 ukutshintshela ezantsi, kwaye ikhowudi yamacandelo asixhenxe iya kudanyaza ukubonisa umgangatho wokuqala (ukufunda ukusuka ezantsi ukuya phezulu, ukungagqibeki ngumgangatho ophantsi, ukufunda ukusuka phezulu ukuya ezantsi, ukungagqibeki ngumgangatho ophezulu). | |
| 3 | Guqula i-SW2 itshintshele phezulu okanye ezantsi ukutshintsha ixabiso elibonisiweyo lomgangatho wokuqalisa. Cinezela u-SW1 tshintshela phantsi imizuzwana eyi-1.5 ukuqalisa ukufunda ngendawo yomgangatho ukusuka kumgangatho wokuqala obonisiweyo. | Ngexesha lokuqala ufunda, unokuqala ukusuka kumgangatho ophantsi okanye kumgangatho ophezulu. Nceda ugqibezele ukufunda ngexesha elinye. |
| 4 | Ukuba ufaka imodi yokufunda yesikhundla somgangatho ngempumelelo, ikhowudi yamacandelo asixhenxe iya kuyeka ukukhanya kwaye ibonise umgangatho wokuqala, i-IC iya kubonisa uluhlu lolawulo, kwaye iqhosha le-BC lomgangatho oza kufundiswa liza kuqala ukukhanya. Ukuba ukungena kwimowudi yokufunda yendawo yomgangatho ayiphumeleli, i-E1 iya kuboniswa. | Xa ufunda okokuqala, inqanaba lolawulo elibonakaliswe yi-IC linokungachanekanga (ngokuqhelekileyo libonisa umgangatho ophezulu). Iya kulungelelanisa ngokuzenzekelayo emva kokufunda umgangatho. |
| 5 | Emva kokungena ngempumelelo kwimodi yokufunda yesikhundla somgangatho, i-elevator iya kuvula umnyango ngokukhawuleza. Qhubeka ucofa iqhosha lokuvala umnyango ngaphakathi kwemoto kwaye i-elevator iya kuvala ucango. Ukukhulula iqhosha lokuvala umnyango ngexesha lenkqubo yokuvala kwaye i-elevator iya kuvula umnyango. | |
| 6 | Umqhubi wemoto ulinganisa ubude bokuphakama kwe-X phakathi komnyango womgangatho we-sill kunye ne-sill yemoto (ukuphakama ngaphezu kwemoto akubi, kwaye ukuphakama ngaphantsi kwemoto kulungile, nge-mm). Ukuba ukuchaneka komgangatho kuhlangabezana neemfuno [-3mm, 3mm], qhubela phambili ngokuthe ngqo kwisinyathelo esilandelayo. | |
| 7 | Okokuqala cofa iqhosha lomgangatho kwibhokisi yokulawula ephambili, uze ucinezele kwaye ubambe iqhosha lokuvula umnyango ngaphezu kwemizuzwana ye-3, kwaye i-elevator iya kungena kwimowudi yexabiso lokutenxa. | Emva kokungena kwimowudi yexabiso lokutenxa, i-IC iya kubonisa 4 |
| 8 | Emva kokukhulula iqhosha, vula ucango lwangaphambili kwaye uvale amaqhosha ukutshintsha ixabiso lokutenxa eliboniswe kwi-IC ukuya ku-X (nge-mm, utolo oluya phezulu lulayita ukubonisa ukuba kulungile, kwaye utolo olusezantsi lulayita ukubonisa okungalunganga). Ukucofa kunye nokubamba iqhosha lokuvula umnyango kuya kwandisa ixabiso lokutenxa, kwaye ukucofa kunye nokubamba iqhosha lokuvala umnyango kuya kunciphisa ixabiso lokutenxa. Uluhlu lohlengahlengiso [-99mm, -4mm] kunye [4mm, 99mm]. | Ukuba ukuphambuka kokuchaneka komgangatho kukhulu, kunokulungiswa ngamaxesha amaninzi |
| 9 | Okokuqala cofa iqhosha lomgangatho kwibhokisi yolawulo ephambili, emva koko ucinezele kwaye ubambe iqhosha lokuvala umnyango ngaphezu kwemizuzwana ye-3, kwaye i-elevator iya kuphuma kwimowudi yexabiso lokutenxa. | Emva kokuphuma kwimowudi yexabiso lokutenxa, i-IC izakubonisa u-0 kunye notolo oluya phezulu |
| 10 | Umsebenzisi osemotweni ukhulula iqhosha kwibhokisi yokulawula umnyango wangaphambili aze aqhubeke ecofa iqhosha lokuvala ucango emotweni. I-elevator iya kuqala emva kokuba umnyango uvaliwe ngokupheleleyo. Emva kokuqala, khulula iqhosha lokuvala umnyango. I-elevator iyakumisa kwaye ivule umnyango emva kokubaleka umgama ongu-X. | |
| 11 | Umsebenzisi kwimoto ulinganisa umahluko wobude phakathi kwe-sill yemoto kunye ne-sill yomnyango womgangatho. Ukuba ingaphandle [-3mm, 3mm], phinda amanyathelo [6] ukuya [11]. Ukuba ingaphakathi [-3mm, 3mm], imfuno yokuchaneka komgangatho ifezekisiwe. | |
| 12 | Umntu osebenza kule moto uqale acofe iqhosha lokuvula ucango emotweni, aze acofe kabini iqhosha lokuvala ucango. I-elevator iya kurekhoda indawo yomgangatho wangoku. Ukuba ukurekhoda kuphumelele, iqhosha elidanyazayo le-BC liya kuxhuma kumgangatho olandelayo ukuze ufundwe, kwaye i-IC iya kubonisa umgangatho wangoku. Ukuba ayiphumelelanga, iya kubonisa i-E2 okanye i-E5. | Vula umnyango + cofa kabini iqhosha lokuvala umnyango |
| 13 | Umsebenzisi kwimoto ubhalisa umyalelo wemoto womgangatho olandelayo (iqhosha elikhawulezayo elikhawulezayo), kwaye uhlala ecofa iqhosha lokuvala ucango lwemoto. Emva kokuba ucango lwe-elevator luvalwe ngokupheleleyo, luya kuqala, lumise kwaye luvule umnyango emva kokubaleka kumgangatho olandelayo. | |
| 14 | Phinda amanyathelo [6] ukuya [12] de yonke imigangatho ifundwe ngempumelelo kwaye ikhowudi yamacandelo asixhenxe kunye ne-IC iya kubonisa F. | |
| 15 | Umsebenzisi okwigumbi lomatshini okanye i-ETP icofa i-SW1 ezantsi kunye ne-SW2 ukuya phezulu kwimizuzwana emi-3, kwaye ilifti iya kuphuma kwimowudi yokufunda yendawo yomgangatho. Ukuba isifundo siphumelele, ikhowudi yamacandelo asixhenxe kunye ne-IC iya kubonisa i-FF. Ukuba isifundo asiphumeleli, ikhowudi yamacandelo asixhenxe kunye ne-IC iya kubonisa i-E3 okanye i-E4. | |
| 16 | Cwangcisa i-SET1/0 ukuya ku-0/8 kwaye ucinezele i-SW1 icitsha ezantsi. | |
| 17 | Seta kwakhona ibhodi ye-P1 okanye ucime i-elevator uze uyivule kwakhona. | Ungaphoswa yiyo! |
Qaphela: Amanyathelo 7-9 angafaka ixabiso lokutenxa nge-APP. Umsebenzisi kwimoto unokusebenzisa ngokuthe ngqo i-APP ukufaka ixabiso lokutenxa kwaye emva koko uqinisekise ukusebenza.
Inyathelo le-12 linokurekhoda indawo yangoku nge-APP. Umsebenzisi emotweni unokusebenzisa ngokuthe ngqo i-APP ukurekhoda indawo yangoku yomgangatho (qinisekisa ukulinganisa)
Iintsingiselo zeekhowudi zamacandelo asixhenxe okanye iziboniso ze-IC ziboniswe kolu luhlu lulandelayo:
| Uluhlu 7 Intsingiselo yekhowudi yamacandelo asixhenxe | |
| Ikhowudi yamacandelo asixhenxe okanye umboniso we-IC | Intsingiselo |
| E1 | Ayiphumelelanga ukufaka imo yokubhala umaleko |
| E2 | Ayiphumelelanga ukurekhoda ulwazi lwendawo yomgangatho |
| E3 | Ayiphumelelanga ukuphuma kwimo yokubhala umaleko |
| E4 | I-ZFS-ELE200 ayiphumelelanga ukubhala ulwazi lomgangatho wendawo |
| E5 | Idatha yendawo yomgangatho ayinangqiqo |
| F | Yonke imigangatho kwicala lokufunda (phezulu okanye ezantsi) ifundwe ngempumelelo |
| FF | Bhala idatha yomgangatho ngempumelelo |
Xa ukubhalwa komgangatho ngokuzenzekelayo akunakwenziwa ngenxa yeempazamo kwitafile yomgangatho osetiweyo, ukutenxa okukhulu kubunjineli boluntu, okanye ukucwangciswa kwebhokisi yokusebenza kwezitshixo ezilishumi, ukubhala phantsi komgangatho kungasetyenziswa.
| Uluhlu lwesi-8 Amanyathelo okubhala ngokuzenzekelayo idatha yomaleko | ||
| Inombolo yesiriyeli | Amanyathelo okulungisa | Ukulumkela |
| 1 | Misa i-elevator kumgangatho ophantsi okanye kwindawo yomnyango ophezulu kwaye utshintshe i-elevator kwindlela yokulondoloza. | |
| 2 | Cwangcisa i-SET1/0 ukuya ku-5/3 (ukufunda ukusuka ezantsi ukuya phezulu) okanye i-5/4 (ukufunda ukusuka phezulu ukuya ezantsi), cinezela u-SW1 ukutshintshela ezantsi, kwaye ikhowudi yamacandelo asixhenxe iya kudanyaza ukubonisa umgangatho wokuqala (ukufunda ukusuka ezantsi ukuya phezulu, ukungagqibeki ngumgangatho ophantsi, ukufunda ukusuka phezulu ukuya ezantsi, ukungagqibeki ngumgangatho ophezulu). | |
| 3 | Guqula i-SW2 itshintshele phezulu okanye ezantsi ukutshintsha ixabiso elibonisiweyo lomgangatho wokuqalisa. Cinezela u-SW1 tshintshela phantsi imizuzwana eyi-1.5 ukuqalisa ukufunda ngendawo yomgangatho ukusuka kumgangatho wokuqala obonisiweyo. | Ngexesha lokuqala ufunda, unokuqala ukusuka kumgangatho ophantsi okanye kumgangatho ophezulu. Nceda ugqibezele ukufunda ngexesha elinye. |
| 4 | Ukuba ukungena kwimodi yokufunda yomgangatho womgangatho kuphumelele, ikhowudi yamacandelo asixhenxe iya kuyeka ukukhanya, kwaye ikhowudi yamacandelo asixhenxe kunye ne-IC iya kubonisa umgangatho wokuqala. Ukuba ukungena kwimowudi yokufunda yesikhundla somgangatho ayiphumeleli, i-E1 iya kuboniswa. | |
| 5 | Umsebenzisi ongaphakathi kwemoto okanye phezulu kwimoto uvula umnyango we-elevator, kwaye umqhubi ngaphakathi kwemoto ulinganisa ubude bokuphakama kwe-X phakathi kwe-sill yomnyango womgangatho kunye ne-sill yemoto (ukuphakama ngaphezu kwemoto kubi, kunye nokuphakama okungaphantsi kwemoto kulungile, iyunithi ngu-mm. Ukuba ukuchaneka komgangatho kuhlangabezana neemfuno [-3mm, 3mm], qhubela phambili ngokuthe ngqo kwisinyathelo esilandelayo). | |
| 6 | Ukuba i-X ingaphandle koluhlu lwe- [-20, 20] mm, imowudi yokusebenza yesantya esisezantsi iyamkelwa ukulungelelanisa ukuchaneka komgangatho ngaphakathi koluhlu [-20, 20] mm. | |
| 7 | Indlela yokusebenza yemowudi yesantya esisezantsi yile: ukuba i-X ilungile, indlela yokusebenza iphezulu, kungenjalo isezantsi. Emva kokuba umqhubi wemoto evala ucango lwe-elevator ngesandla, uhlala ecofa iqhosha lokuvala umnyango kwibhokisi yokulawula, aze azise umqhubi ophezu kwemoto yendlela yokusebenza kunye neemfuno zokuqala. Umsebenzisi ophezu kwemoto uya kusebenzisa isixhobo sokwenza umsebenzi wokulungisa ukwenza ilifti iqhube. I-elevator iya kuhamba ngesantya se-2.1m / min. Kwangaxeshanye, umboniso okwinqwelo-mafutha (IC) uya kubonisa umgama ohanjwe ngulo msebenzi (nge-mm, utolo oluya phezulu lulayitelwa i-positive, kwaye utolo olusezantsi lulayitelwe negative). Xa ixabiso eliboniswe yi-IC lilingana no-X, umqhubi wemoto ukhulula iqhosha lokuvala umnyango kwibhokisi yokulawula, kwaye i-elevator iyakuyeka ukusebenza (i-slow stop). Emva kokuba i-elevator iyeka ngokuthe ngcembe, umqhubi ophezu kwemoto unokurhoxisa umyalelo wokulungisa. | |
| 8 | Ukuba i-X ingaphakathi koluhlu lwe- [-20, 20] mm, imowudi yokusebenza kwesantya esiphezulu-ephantsi iyamkelwa ukulungelelanisa ukuchaneka komgangatho kuluhlu lwe- [-3, 3] mm. |
|
| 9 | Indlela yokusebenza yendlela yokusebenza yesantya esisezantsi kakhulu yile: ukuba i-X ilungile, indlela yokusebenza iphezulu, kungenjalo isezantsi. Umsebenzisi osemotweni uvala ucango lwe-elevator ngesandla, aze aqhubeke ecofa iqhosha lokuvula ucango kwibhokisi yokulawula, aze azise umqhubi ophezu kwemoto yendlela yokusebenza kunye neemfuno zokuqala. Umsebenzisi ophezu kwemoto uya kusebenzisa isixhobo sokwenza umsebenzi wokulungisa ukwenza ilifti iqhube. I-elevator iya kuqhuba ngesantya se-0.1m / min (ukuba ixesha eliqhubekayo lokusebenza lidlula i-60s, isofthiwe iya kumisa i-elevator). Kwangaxeshanye, umboniso okwinqwelo-mafutha (IC) uya kubonisa umgama ohanjwe ngulo msebenzi (nge-mm, utolo oluya phezulu lulayitelwa i-positive, kwaye utolo olusezantsi lulayitelwe negative). Xa ixabiso eliboniswe yi-IC lilingana no-X, umqhubi wemoto ukhulula iqhosha lokuvula umnyango, kwaye i-elevator iya kuyeka ukusebenza (i-slow stop). Emva kokuba i-elevator iyeka ngokuthe ngcembe, umqhubi ophezu kwemoto uya kurhoxisa umyalelo wokusebenza wokulondoloza. | |
| 10 | Phinda amanyathelo [5] ukuya [9] de ukuchaneka komgangatho kulungelelaniswa ngaphakathi koluhlu [-3, 3] mm. | |
| 11 | Lushiye luvuliwe ucango lweelevator, umntu osebenza emotweni ucofa iqhosha lokuvula ucango, aze acofe kabini iqhosha lokuvala ucango. I-elevator iya kurekhoda indawo yomgangatho wangoku. Ukuba ukurekhoda kuphumelele, umgangatho obonisiweyo uya kwanda ngo-1 (ukufunda ukusuka phezulu ukuya phezulu) okanye unciphise ngo-1 (ukufunda ukusuka phezulu ukuya phezulu). Ukuba ayiphumelelanga, i-E2 okanye i-E5 iya kuboniswa. | |
| 12 | Vala ucango lwe-elevator, kwaye umqhubi ophezu kwemoto usebenzisa isixhobo esiqhuba ukugcinwa kwe-elevator ukwenza i-elevator iqhube ngesantya sokulondoloza de i-elevator ibaleke ukuya kwindawo yomnyango kumgangatho olandelayo ukuze ifundwe kwaye ime. | |
| 13 | Phinda amanyathelo [5] ukuya [12] de yonke imigangatho ifundwe ngempumelelo kwaye ikhowudi yamacandelo asixhenxe kunye ne-IC iya kubonisa F. | |
| 14 | Umsebenzisi okwigumbi lomatshini okanye i-ETP icofa i-SW1 ezantsi kunye ne-SW2 ukuya phezulu kwimizuzwana emi-3, kwaye ilifti iya kuphuma kwimowudi yokufunda yendawo yomgangatho. Ukuba isifundo siphumelele, ikhowudi yamacandelo asixhenxe kunye ne-IC iya kubonisa i-FF. Ukuba isifundo asiphumeleli, ikhowudi yamacandelo asixhenxe kunye ne-IC iya kubonisa i-E3 okanye i-E4. | |
| 15 | Cwangcisa i-SET1/0 ukuya ku-0/8 kwaye ucinezele i-SW1 icitsha ezantsi. | |
| 16 | Seta kwakhona ibhodi ye-P1 okanye ucime i-elevator uze uyivule kwakhona. | Ungaphoswa yiyo! |
Iintsingiselo zeekhowudi zamacandelo asixhenxe okanye iziboniso ze-IC ziboniswe kolu luhlu lulandelayo:
| Uluhlu 9 Intsingiselo yekhowudi yamacandelo asixhenxe | |
| Ikhowudi yamacandelo asixhenxe okanye umboniso we-IC | Intsingiselo |
| E1 | Ayiphumelelanga ukufaka imo yokubhala umaleko |
| E2 | Ayiphumelelanga ukurekhoda ulwazi lwendawo yomgangatho |
| E3 | Ayiphumelelanga ukuphuma kwimo yokubhala umaleko |
| E4 | I-ZFS-ELE200 ayiphumelelanga ukubhala ulwazi lomgangatho wendawo |
| E5 | Idatha yendawo yomgangatho ayinangqiqo |
| F | Yonke imigangatho kwicala lokufunda (phezulu okanye ezantsi) ifundwe ngempumelelo |
| FF | Bhala idatha yomgangatho ngempumelelo |