Shanghai Mitsubishi LEHY-Pro (NV5X1) Elevator Low-speed Operation Debugging Essentials
1.Kugadzirira kusati kwakaderera kushanda
①. Kana paine chekuchengetedza magetsi emagetsi echimbichimbi, wiring yemanyorero inodiwa kuchengetedza yakajairwa yekuzivikanwa kwemagetsi relay #NOR mudunhu.
Short-circuit iyo 420 (ZTNO-01) uye NORR (ZTNO-02) zviteshi paZ1 board.
②. Shandura chinja chekuchinja "DRSW/IND" pachishandiso chemunhu-muchina chekudyidzana kuenda panzvimbo yepakati kuti usunungure nzvimbo yakachekwa yegonhi mumatanho apfuura.
③. Kana dunhu rekuchengetedza rakajairika, iyo LED inoenderana pane yemunhu-muchina yekudyidzana mudziyo unofanirwa kuvhenekera. Kana chero chekuchengetedza cheki switch yakabviswa, LED 29 inofanira kunge yakadzimwa.
(1) Mhanya/Misa chinja pane muchina kamuri yekudzora bhokisi;
(2) Mhanya/Misa chinja pamotokari yepamusoro chiteshi chekudzora bhokisi;
(3) Mhanya / Stop switch pane gomba rekushanda bhokisi;
(4) Muchina wekamuri yekumisa switch (kana iripo);
(5) Motokari yepamusoro yekubuda kwechimbichimbi switch (kana iripo);
(6) Motokari yekuchengetedza chivharo chinja (inogona kupfupika-yakatenderedzwa yekukurumidza kushanda kwemagetsi);
(7) Hoistway emergency kubuda switch (kana iripo);
(8) Gomba gonhi switch (kana iripo);
(9) Pit stop switch (kusanganisira yechipiri gomba yekumisa switch (kana iripo));
(10) Car side speed limiter tensioner switch (inogona kupfupika-inotenderera kune emergency magetsi kushanda);
11
(12) Counterweight side buffer switch (inogona kupfupika-inotenderera kune emergency magetsi kushanda);
(13) Mota yedivi buffer switch (inogona kupfupika-yakatenderedzwa yekukurumidza kushanda kwemagetsi);
(14) Terminal muganho chinja TER.SW (inogona kupfupika-circuited kana emergency magetsi oparesheni);
(15) Magetsi switch yekumhanyisa limiter padivi remota (inogona kupfupika-inotenderedzwa kana ye emergency magetsi oparesheni);
(16) Kuchinja kwemagetsi kwechimbichimbi chekumhanyisa parutivi (kana paine) (inogona kupfupika-inotenderedzwa kana paine emergency yemagetsi oparesheni);
(17) Manual turning switch (kana iripo);
(18) Side door lock switch (yakagadzirirwa ADK);
(19) Emergency exit switch at floor station (kana iripo);
(20) Kuchinja kwemanera mugomba (kana iripo);
(21) Kubhadhara vhiri switch (kana iripo);
(22) Magnetic scale bhanhire tensioning switch (kana iripo) (inogona kupfupika-inotenderera kana paine emergency yemagetsi oparesheni);
(23) Waya tambo slack uye yakatyoka tambo switch (yakagadzirirwa nzira yeRussia).
④. Kana mabhatani ekumhanya uye kumusoro / pasi echimbichimbi emagetsi oparesheni akatsikirirwa panguva imwe chete uye zvichienderera, anotevera anoburitsa chiedza-emitting diode uye macontactor anofanirwa kushanda mukutevedzana.
Kana bhatani reKumusoro/Kudzika rikadzvanywa nguva dzose, iyo LED uye contactor inobuda kana kusunungura, uye yodzokorora kutevedzana kuri pamusoro ka3. Izvi zvinodaro nekuti mota haina kubatana uye TGBL (yakanyanya kuderera kumhanya) kukanganisa kunokonzereswa.
⑤. Dzima madhigirii edunhu MCB neCP.
⑥. Batanidza zvekare tambo dzemota dzakabviswa U, V, W uye tambo dzebrake coil zvinoenderana newaya yekutanga.
Kana iyo brake tambo yekubatanidza isina kubatana kune control cabinet, maitiro ekushanda haatange.
⑦. Iyo yakaderera-kumhanya kushanda inogona kushandirwa mukamuri yemuchina uchishandisa switch pane yekukurumidzira magetsi oparesheni mudziyo. Mushure mekutarisa iyo encoder wiring, iwe zvakare unofanirwa kutarisa oparesheni switch pamusoro pemotokari.
2.Nyora kune magnetic pole position
Matanho anotevera anogona kuitwa chete mushure mekuona kuti magonhi epasi uye magonhi emotokari akavharwa zvakachengeteka.
| Tafura 1 Magnetic pole position kunyora matanho | |||
| Siriyero nhamba | Kugadzirisa matanho | Zvekungwaririra | |
| 1 | Tarisa kuti tambo dzemota U, V, W uye tambo dzemabhureki dzakanyatsobatanidzwa kune kabati yekudzora. | ||
| 2 | Ita shuwa kuti wedunhu breaker CP mukati mekutonga kabati yakavharwa. | ||
| 3 | Simbisa kuti lift inosangana nemamiriro ekushanda kwakaderera. Simbisa kuti (NORMAL/EMERGENCY) switch yechimbichimbi yemagetsi oparesheni yatendeudzirwa kudivi re(EMERGENCY). | ||
| 4 | Gadzirisa chinja chinotenderera SET1/0 pachigadzirwa chemunhu-muchina kuenda ku0/D, uye kodhi yezvikamu zvinomwe ichapenya kuratidza A0D. |
| |
| 5 | Dzvanya SW1 switch pane yemunhu-muchina interface ichidzika kamwe, iyo-segment-segment kodhi inopenya nekukasira, uye ipapo ikozvino magineti pole chinzvimbo icharatidzwa. | Dzvanya SW1 kekutanga | |
| 6 | Dzvanya SW1 switch pamunhu-muchina interface mudziyo pasi zvakare (inenge 1.5 masekonzi) kusvikira nomwe-chikamu kodhi kodhi yaratidza PXX (XX ndiyo yazvino synchronization layer. Kana layer isina kunyorwa, iyo inoratidzwa synchronization layer inogona kunge isiriyo). | Dzvanya SW1 kechipiri | |
| 7 | Emergency electric operation, kusvika 7-segment code ichiratidza hutsva hwemagnetic pole position, uye elevator haina kumira kamwe kamwe, iyo magnetic pole position inonyorwa zvinobudirira. | Ndokumbira utarise kana kukosha kwemagineti danda kuchichinja sechikonzero chekubudirira kunyora. | |
| 8 | Seta chinotenderera SET1/0 pamudziyo wekudyidzana nemunhu kusvika pa0/8, wodzvanya uye ubate SW1 chinja kusvika pasi kodhi yezvikamu zvinomwe yatanga kupenya nekukasira, wobva wabuda muSET modhi. | ||
3. Low speed operation
Kana yakashongedzerwa neiyo shaft information system, iyo yakakwana chinzvimbo sensor ine maviri masisitimu, anoti magineti chiyero uye kodhi tepi. Nekuda kwekureruka, iyo magineti chiyero uye kodhi tepi inorehwa pamwe chete sezviyero mune inotevera chinyorwa.
Chikero chisati chaiswa, pinda muyero yekuisa modhi kutanga, ona 5.
Mushure mekudzvanya magetsi ekukurumidzira kana kugadzirisa kumusoro uye bhatani rekuraira, iyo LED UP pane yemunhu-muchina yekudyidzana mudziyo unofanirwa kuvheneka uye mota inofanira kukwira. Mushure mekudzvanya bhatani rekudzika nekuraira, iyo LED DN pane yemunhu-muchina wekudyidzana mudziyo unofanirwa kuvheneka uye mota inofanira kudzika. Kana mota iri yakareruka pane counterweight, mota inogona kunge ichikwira kumusoro uye yobva yadzika zvakajairika. The manual operation speed is 15m/min.
Munguva yemanyorero ekugadzirisa debugging, inofanirwa kusimbiswa kuti bhureki rinogona kuvhurwa zvakazara uye muchina wekukwevera hauna ruzha uye kudedera.
Uye zvakare, kana mota yamira, mabhureki ekubatanidza anofanirwa kuvharwa zvizere kuti ave nechokwadi chekushanda kwebhureki.
Munguva yekushanda kwemanyorero, mota inofanirwa kumira nekukurumidza kana dunhu rekuchengetedza rakadai seyekuchengetedza switch, gonhi repasi kana mota yekuvhara gonhi switch inobviswa.
Munguva yese yekuisa uye kugadzirisa maitiro, kuitira kudzivirira mota kubva pakupisa nekuda kwekupfuura, pfungwa dzinotevera dzinofanirwa kubatwa nekuchenjerera kukuru.
I. Cheni yekubhadhara inofanira kusungirirwa isati yatanga kushanda zvishoma.
Kana cheni yekubhadhara isina kusungirirwa panguva yakaderera-kumhanya kwekushanda, mota ichashanda pasi pemamiriro ekupfuura yakayerwa ikozvino. Nokudaro, kana pasina chido chakakosha, mamiriro ezvinhu ari pamusoro apa anofanira kudziviswa. Kana zvichidikanwa kushanda nekumhanya kwakaderera pasina kurembera ketani yekubhadhara, zvinodikanwa kuwedzera mutoro wakakodzera mumotokari kuti uenzanise uremu hweanopikisa. Kana iyo sitiroko ichipfuura 100 metres, zvinodikanwa kuti utarise iyo mota ikozvino kuti uone kuti ikozvino haipfuure 1.5 nguva yakatarwa ikozvino.
Kana iyo mota yazvino inodarika 1.5 times the rated value, mota ichapisa mukati memaminitsi mashoma.
II. Matanho ekurembera uye zvinodiwa zveketani yekuripa zvinofanirwa kureva chikamu chemuchina chekuisa uye kugadzirisa ruzivo.
III. Mushure mekunge cheni yekubhadhara yarembera, mota inofanirwa kutakurwa nemutoro wekuenzanisa counterweight uye kumhanya yakaderera kusvika chiyero chekuenzanisa chaedzwa.
Ongorora: Kana iyo scaffolding-yemahara yekuisa maitiro ikagamuchirwa, zvinodikanwa kushandisa scaffolding-yemahara yakakosha tooling uye kupinda muchikafu-yemahara yekuisa modhi yekufambisa mota.
4. Kudzidza pasi nePAD
Kana yakashongedzerwa nePAD, dhizaini yekunyora mashandiro anogona chete kuitwa mushure meiyo terminal deceleration switch, magineti yekuzviparadzanisa nevamwe ndiro, kuyera uye kukwirisa-leveling switch mutsime yakaiswa.
Kana yakashongedzerwa netsime ruzivo system, hapana kushanda kwakadaro.
| Tafura 2 Floor kudzidza matanho kana akashongedzerwa PAD | ||
| Siriyero nhamba | Kugadzirisa matanho | Zvekungwaririra |
| 1 | Emergency electric operation inomisa mota pafloor yepazasi re-leveling area. | |
| 2 | Gadzirisa chinja chinotenderera SET1 pachigadzirwa chemunhu-muchina ku0 uye SET0 kusvika ku7, uye kodhi yezvikamu zvinomwe ichapenya uye kuratidza A07. | SET1/0=0/7
|
| 3 | Dzvanya uye ubate switch yeSW1 pane yemunhu-muchina interface mudziyo kusvika kodhi yezvikamu zvinomwe yatanga kupenya nekukurumidza, uyezve F01 icharatidzwa. | Dzvanya SW1 kekutanga
|
| 4 | Dzvanya uye ubate switch yeSW1 pane yemunhu-muchina interface mudziyo pasi zvakare kudzamara nomwe-chikamu kodhi yatanga kupenya, uye ipapo F00 icharatidzwa. | Dzvanya SW1 kechipiri
|
| 5 | Mhanya mota nemaoko ukaramba uchibva pauriri hwepasi kusvika pauriri hwepamusoro uye wozoenda kunzvimbo yekuenzanisa. | |
| 6 | Iyo elevator inongomira kumhanya uye nomwe-chikamu kodhi inomira kupenya, zvichiratidza kuti kunyora pasi kuri kubudirira. | |
| 7 | Kana motokari ikamira isati yasvika pauriri hwepamusoro, dzokorora nhanho (1)-(5). | Kana iyo data yehurefu hwepasi isingakwanise kunyorwa, tarisa chinzvimbo chechiitiko cheiyo terminal yekumisikidza switch, yekumisikidza/kurevesazve mudziyo uye encoder. |
| 8 | Dzosera ma rotary switch SET1 uye SET0 pane yemunhu-muchina yekudyidzana mudziyo ku0 uye 8 zvakateerana. | SET1/0=0/8 |
| 9 | Dzvanya uye ubate switch yeSW1 pane yemunhu-muchina interface mudziyo kudzamara nomwe-chikamu kodhi yatanga kupenya nekukasira kubuda muSET modhi. | |
5. Kudzidza pasi paunenge uchigadzirisa shaft information system
5.1 Scale Installation
Kana yakashongedzerwa neshaft information system, iyi modhi inogona kungopinzwa kana uchiita chiyero chekuisa mashandiro uye yenguva nhanho yekudzidza chinzvimbo. Zvinorambidzwa kupinda iyi modhi mune zvimwe zviitiko!
Mushure mokunge chiyero chaiswa, nzvimbo yemuganhu yenguva inonyorwa pakarepo.
Kana yakashongedzerwa nePAD, hapana kushanda kwakadaro.
| Tafura 3 Kupinda uye kubuda kwechiyero chekuisa | ||
| Siriyero nhamba | Kugadzirisa matanho | Zvekungwaririra |
| 1 | Ita shuwa kuti lift iri musimba rekukurumidzira kana maitiro ekuongorora. | |
| 2 | Gadzirisa chinja chinotenderera SET1 pachigadzirwa chemunhu-muchina ku2 uye SET0 kuA, uye kodhi yezvikamu zvinomwe ichapenya uye kuratidza A2A. | SET1/0=2/A
|
| 3 | Dzvanya SW1 switch pane yemunhu-muchina interface yekudzika pasi kamwe, uye nomwe-chikamu kodhi inopenya nekukasira, uye ipapo icharatidza "kudzima" pasina kupenya. | Dzvanya SW1 kekutanga
|
| 4 | Dzvanya uye bata switch yeSW1 pamuchina-muchina wekushandisa pasi (angangoita masekonzi 1.5) kusvika kodhi yezvikamu zvinomwe yatanga kupenya zvishoma nezvishoma. | Dzvanya SW1 kechipiri |
| 5 | Shandura iyo RESET switch yeZFS-ELE200 mukati megumi (inoshanda kwenguva yekubata ye [0.5s, 10s]). | Tora reset switch paZFS-ELE200 |
| 6 | Iyo 7-segment kodhi icharatidza "pa", uye iyo chiyero yekuisa modhi yakapinda zvakabudirira. |  |
| 7 | Kana iyo 7-segment kodhi inoratidza "pa", iwe unofanirwa kutenderedza iyo RESET switch yeZFS-ELE200 zvakare kuti ubvise zvikanganiso zvine chekuita neZFS-ELE200, uye kodhi yezvikamu zvinomwe icharatidza "pa". | Kana iyo dijitari chubhu isingaratidzi ".", iwe unofanirwa kutenderedza reset switch zvakare. |
| 8 | Ita chiyero chekuisa. Kana magetsi ekukurumidzira kana mashandiro ekugadzirisa akaitwa muchiyero chekuisa modhi, iyo mota yepamusoro buzzer inonzwika. |
|
| 9 | Mushure mekugadzwa kwerumu kwapera, dzvanya uye ubate SW1 switch pane yemunhu-muchina interface mudziyo (angangoita masekonzi 1.5) kudzamara segment-segment code ibuditsa OFF kuti ubude murura yekuisa modhi. | |
Cherechedza:
①. Pamusoro pemabasa ari pamusoro apa, kushandura SET1/0 chinja kubva pa2/A kana kusetazve bhodhi reP1 kunozobuda otomatiki pachiyero chekuisa modhi;
②. Tsanangudzo yezvikamu zvinomwe kodhi inoratidzwa pakupinda nekubuda muyero yekuisa modhi inoratidzwa mune inotevera tafura:
| Tafura 4 Zvinoreva kodhi yezvikamu zvinomwe | |
| Seven-segment display | Kureva |
| on | Iyo elevator yapinda muyero yekuisa modhi uye inoda kudzima ZFS-ELE200 ine chekuita nekukanganisa. |
| on | Elevator yapinda pachiyero chekuisa mode |
| off | Elevator yabuda pachiyero chekuisa modhi |
| E1 | Nguva yekupera kana uchipinda kana kubuda mutongi yekuisa modhi |
| E2 | Iyo RESET switch haishandiswe mukati memasekonzi gumi kana ichipinda muyero yekuisa modhi. |
| E3 | SDO ruzivo kunze |
5.2 Kunyora kwechinzvimbo chenguva pfupi
Kana iyo shaft yeruzivo system yakashongedzerwa, kana nzvimbo yenguva pfupi isati yanyorwa, lifti inofanirwa kunge iri mukugadzirisa maitiro isati yapinda muyero yekuisa modhi. Usadzima simba paunenge uchinyora nzvimbo yepamusoro/yakaderera yenguva pfupi.
Mushure mekunge nzvimbo yekumusoro/yakaderera yenguva pfupi yanyorwa, lifti ichava neiyo terminal kuchengetedza basa. Kana magetsi echimbichimbi kana mashandiro ekugadzirisa asvika padanho repagonhi repasi, lifti inofanira kumira kumhanya zvakajairika.
Kana yakashongedzerwa nePAD, hapana kushanda kwakadaro.
| Tafura 5 Yenguva inogumira chinzvimbo chekunyora matanho | ||
| Siriyero nhamba | Kugadzirisa matanho | Zvekungwaririra |
| 1 | Iyo mota yepamusoro opareta inomhanyisa mota yekusimudza kuenda kune yepamusoro yenguva diki muganhu chinzvimbo (UOT chiito) kuburikidza nekugadzirisa. | Simbisa nzvimbo yekuisa switch zvinoenderana nedhirowa yekuisa |
| 2 | Mushandi ari muimba yekombuta anogadzirisa shanduko ye rotary SET1 pamudziyo wekubatana kwevanhu-muchina ku5 uye SET0 kusvika ku2, uye kodhi yezvikamu zvinomwe ichapenya kuratidza A52. | SET1/0=5/2
|
| 3 | Dzvanya SW1 switch pane yemunhu-muchina interface yekudzika pasi kamwe, nomwe-chikamu kodhi inopenya nekukasira, uye yobva yapenya zvishoma nezvishoma kuratidza yepamusoro yechinguva muganhu chinzvimbo mune yazvino parameter. | Dzvanya SW1 kekutanga |
| 4 | Dzvanya uye bata switch yeSW1 pamuchina-muchina wekudyidzana pasi (kweinenge 1.5 seconds) kusvika kodhi yezvikamu zvinomwe yatanga kupenya nekukasira. Mushure mekunyora kwapera, iyo 7-segment kodhi inomira kupenya uye kuratidza yepamusoro yenguva muganhu chinzvimbo muparameter. Kana kunyora kukundikana, E icharatidzwa. | Dzvanya SW1 kechipiri |
| 5 | Mushandi ari pamusoro pemotokari anodzorera shanduko yekugadziridza kune yakajairwa, uye anoshanda mukamuri yemuchina anoita basa remagetsi rekukurumidzira kufambisa lifti ichidzika pasi uye kunze kwenzvimbo yepamusoro yenguva pfupi (UOT). | Inoda kushanda nevashandi mukamuri yemuchina |
| 6 | Shandura iyo ZFS-ELE200's RESET switch kuti ubvise ZFS-ELE200 zvine hukama zvikanganiso. | |
| 7 | Opareta ari pamusoro pemotokari anomhanyisa mota yekusimudza kuenda kunzvimbo yepasi yenguva pfupi (DOT chiito) kuburikidza nekugadzirisa. | |
| 8 | Mushandi ari muimba yekombuta anogadzirisa shanduko ye rotary SET1 pamudziyo wekubatana kwevanhu-muchina ku5 uye SET0 kusvika ku1, uye kodhi yezvikamu zvinomwe ichapenya kuratidza A51. | SET1/0=5/1 |
| 9 | Dzvanya SW1 switch pane yemunhu-muchina interface yekudzika pasi kamwe, iyo-segment-segment kodhi ichapenya nekukasira, uye yobva yapenya zvishoma nezvishoma kuratidza yakaderera yechinguvana muganhu chinzvimbo mune yazvino parameter. | Dzvanya SW1 kekutanga |
| 10 | Dzvanya uye bata switch yeSW1 pamuchina-muchina wekudyidzana pasi (kweinenge 1.5 seconds) kusvika kodhi yezvikamu zvinomwe yatanga kupenya nekukasira. Mushure mekunyora kwapera, iyo nomwe-chikamu kodhi inomira kupenya uye kuratidza yakaderera yenguva muganhu chinzvimbo muparameter. Kana kunyora kukundikana, E icharatidzwa. | Dzvanya SW1 kechipiri |
| 11 | Mushandi ari pamusoro pemotokari anodzoreredza switch yekuongorora kune yakajairwa, uye anoshanda mukamuri yemuchina anoita basa remagetsi rekukurumidzira kufambisa lifti kumusoro kunze kwenzvimbo yepasi yenguva pfupi (DOT). | Inoda kushanda nevashandi mukamuri yemuchina |
| 12 | Gadzirisa P1 bhodhi kana kudzima elevator wobva waibatidza zvakare. | Usazvipotsa! |
5.3 Nyora pasi data
Kushanda kwekunyora kunogona kuitwa chete mushure mekunge ZFS-ELE200 yaiswa, mwenje wechiratidzo pabhokisi rekuchengetedza wakajairika, iyo yenguva diki yekumisikidza nzvimbo yekudzidza yakapedzwa, masaini emusuwo esimudziro akajairika (kusanganisira GS, DS, CLT, OLT, FG2, MBS, nezvimwewo), mabhatani ekuvhura nekuvhara gonhi, bhokisi rekudzora mabhatani (BC), iyo mota yekufona system inoshanda nemazvo, IC mota inoshanda nemazvo, mota inosheedzera (IC). blocking mudziyo uri kushanda nemazvo.
Paunenge uchiita layer yekunyora mashandiro, zvinokurudzirwa kuti mumwe munhu arambe ari mukamuri yemechini kuti ape kununura kana mamiriro amuka!
Automatic kunyora layers anodiwa.
| Tafura 6 Matanho ekunyora otomatiki nyora layer data | ||
| Siriyero nhamba | Kugadzirisa matanho | Zvekungwaririra |
| 1 | Misa rifiti pauriri hwepasi kana pauriri hwepamusoro pegonhi uye shandura lifti kuita otomatiki modhi. | Panguva ino, sezvo ZFS-ELE200 isina chiratidzo chechinzvimbo, 29 # mwenje haugone kuvhenekerwa, izvo zvakajairika. |
| 2 | Seta SET1/0 kusvika 5/3 (kudzidza kubva pasi kusvika kumusoro) kana 5/4 (kudzidza kubva kumusoro kusvika pasi), dzvanya SW1 chinja uchidzika, uye nomwe-chikamu kodhi ichapenya kuratidza yekutanga pasi (kudzidza kubva pasi kusvika kumusoro, iyo yakasarudzika ndiyo yepasi pasi, kudzidza kubva kumusoro kusvika pasi, iyo default ndiyo yekumusoro uriri). | |
| 3 | Shandura SW2 chinja kumusoro kana pasi kuti uchinje kukosha kwepasi kunoratidzwa. Dzvanya SW1 chinja pasi kwemasekonzi 1.5 kuti utange kudzidza kwepasi kubva pauriri hwekutanga. | Nguva yekutanga yaunodzidza, iwe unogona chete kutanga kubva pasi pasi kana pauriri hwepamusoro. Ndapota pedzisa kudzidza panguva imwe chete. |
| 4 | Kana ukapinda pasi pekufunda mode yepasi zvinobudirira, iyo 7-segment kodhi inomira kupenya uye kuratidza yekutanga pasi, iyo IC icharatidza manejimendi layer, uye BC bhatani repasi richadzidzwa richatanga kupenya. Kana kupinda pasi nzvimbo yekudzidza modhi ikatadza, E1 icharatidzwa. | Paunenge uchidzidza kekutanga, danho rekutungamirira rinoratidzwa neIC rinogona kunge risina kururama (kazhinji rinoratidza pasi repamusoro). Ichagadzirisa otomatiki mushure mekudzidza pasi. |
| 5 | Mushure mekubudirira kupinda pasi pekufunda maitiro, lifti inovhura musuwo nekukasira. Ramba wakadzvanya bhatani rekuvhara gonhi mukati memotokari uye lifti ichavhara musuwo. Sunungura bhatani rekuvhara gonhi panguva yekuvhara uye lifti ichavhura musuwo. | |
| 6 | Mushandi ari mumotokari anoyera mutsauko wehurefu X pakati pegonhi repasi uye sill yemotokari (kureba pamusoro pemotokari hakuna kunaka, uye kureba pasi pemotokari kwakanaka, mu mm). Kana kurongeka kwekuenzanisa kunosangana nezvinodiwa [-3mm, 3mm], enda zvakananga kune nhanho inotevera. | |
| 7 | Kutanga dzvanya bhatani repasi pane hombe yekudzora bhokisi, wobva wadzvanya uye ubate bhatani rekuvhura gonhi kweanopfuura masekonzi matatu, uye lifti inopinda yekuisa yekutsauka kukosha modhi. | Mushure mekupinda iyo yekutsauka kukosha yekuisa modhi, iyo IC inoratidza 4 |
| 8 | Mushure mekuburitsa bhatani, shandisa gonhi remberi kuvhura uye kuvhara mabhatani kuti uchinje kukosha kwekutsauka kunoratidzwa paIC kuenda kuX (mu mm, museve wekumusoro unovhenekera kumusoro kuratidza zvakanaka, uye museve wepasi unovhenekera kuratidza kuti hauna kunaka). Kudzvanya nekubata gonhi rakavhurika bhatani kunowedzera kukosha kwekutsauka, uye kudzvanya nekubata bhatani rekuvhara gonhi kunoderedza kukosha kwekutsauka. Rudzi rwekugadzirisa ndeye [-99mm, -4mm] uye [4mm, 99mm]. | Kana kutsauka kwepasi kwakakura, kunogona kugadziriswa kakawanda |
| 9 | Kutanga dzvanya bhatani repasi pane hombe yekudzora bhokisi, wobva wadzvanya uye ubate bhatani rekuvhara gonhi kweanopfuura masekonzi matatu, uye lifti inobuda iyo yekupinda yekutsauka kukosha modhi. | Mushure mekubuda muyedzo yekukanganisa kukosha modhi, iyo IC icharatidza 0 uye museve wekumusoro |
| 10 | Mushandi ari mumotokari anoburitsa bhatani pabhokisi rekudzora gonhi repamberi uye anoramba achidzvanya bhatani rekuvhara gonhi mumotokari. Elevator ichatanga mushure mekunge musuwo wavharwa zvakazara. Mushure mekutanga, sunungura bhatani rekuvhara gonhi. Elevator inomira yovhura gonhi mushure mekumhanya X chinhambwe. | |
| 11 | Mushandi ari mumotokari anoyera mutsauko wehurefu pakati pemota sill uye yepasi gonhi sill. Kana iri kunze [-3mm, 3mm], dzokorora nhanho [6] kusvika [11]. Kana iri mukati me [-3mm, 3mm], kuenzana kwechiyero kunodiwa. | |
| 12 | Munhu ari mumotokari anotanga adzvanya bhatani rekuvhura gonhi mumotokari, obva adzvanya kaviri bhatani rekuvhara gonhi. Elevator icharekodha nzvimbo yepasi iripo. Kana kurekodha kwakabudirira, bhatani rinopenya reBC rinosvetukira kune imwe pasi kuti idzidzwe, uye IC icharatidza pasi iripo. Kana ikatadza, icharatidza E2 kana E5. | Vhura musuwo + tinya kaviri bhatani rekuvhara gonhi |
| 13 | Mushandi ari mumotokari anonyoresa mirairo yemotokari yepasi (flashing prompt button), uye anoramba achidzvanya bhatani rekuvhara gonhi remotokari. Mushure mekunge gonhi rekusimudzira ravharwa zvakazara, rinotanga, mira uye vhura musuwo mushure mekumhanya kune inotevera pasi. | |
| 14 | Dzokorora nhanho [6] kusvika [12] kusvikira pasi rose radzidzwa zvinobudirira uye nomwe-chikamu kodhi uye IC icharatidza F. | |
| 15 | Mushandi ari mukamuri yemuchina kana ETP anodzvanya SW1 pasi uye SW2 kumusoro kwemasekonzi matatu, uye lifti inobuda pauriri chinzvimbo chekudzidza modhi. Kana kudzidza kwakabudirira, kodhi yezvikamu zvinomwe uye IC icharatidza FF. Kana kudzidza kwacho kuchitadza, kodhi yezvikamu zvinomwe uye IC icharatidza E3 kana E4. | |
| 16 | Seta SET1/0 kusvika 0/8 wodzvanya SW1 chinja pasi. | |
| 17 | Gadzirisa P1 bhodhi kana kudzima elevator wobva waibatidza zvakare. | Usazvipotsa! |
Cherechedza: Matanho 7-9 anogona kuisa kukosha kwekutsauka kuburikidza neAPP. Mushandi mumotokari anogona kushandisa zvakananga APP kuisa kukosha kwekutsauka uye obva asimbisa kushanda.
Nhanho 12 inogona kurekodha chinzvimbo chiripo kuburikidza neAPP. Mushandi ari mumotokari anogona kushandisa zvakananga APP kurekodha yazvino pasi chinzvimbo (simbisa kuenzana)
Zvinorehwa nemakiyi manomwe-segment macode kana IC maratidziro anoratidzwa mune inotevera tafura:
| Tafura 7 Zvinoreva kodhi yezvikamu zvinomwe | |
| Seven-segment kodhi kana IC kuratidza | Kureva |
| E1 | Yatadza kuisa layer mode |
| E2 | Tatadza kurekodha ruzivo rwenzvimbo yepasi |
| E3 | Yatadza kubuda kunyora layer mode |
| E4 | ZFS-ELE200 yakundikana kunyora ruzivo rwenzvimbo |
| E5 | Iyo data yenzvimbo yepasi haina musoro |
| F | Ese pasi munzira yekudzidza (kumusoro kana pasi) akadzidzwa zvinobudirira |
| FF | Nyora pasi data zvakabudirira |
Kana otomatiki pasi kunyora kusingagone kuitwa nekuda kwezvikanganiso mu preset floor tafura, kutsauka kukuru muinjiniya yehurumende, kana kumisikidzwa kwebhokisi remakiyi gumi, kunyora pasi pasi kunogona kushandiswa.
| Tafura 8 Matanho ekunyora otomatiki nyora layer data | ||
| Siriyero nhamba | Kugadzirisa matanho | Zvekungwaririra |
| 1 | Misa lifti pauriri hwepasi kana pauriri hwepamusoro pegonhi uye shandura lifti kuti iite kugadzirisa. | |
| 2 | Seta SET1/0 kusvika 5/3 (kudzidza kubva pasi kusvika kumusoro) kana 5/4 (kudzidza kubva kumusoro kusvika pasi), dzvanya SW1 chinja uchidzika, uye nomwe-chikamu kodhi ichapenya kuratidza yekutanga pasi (kudzidza kubva pasi kusvika kumusoro, iyo yakasarudzika ndiyo yepasi pasi, kudzidza kubva kumusoro kusvika pasi, iyo default ndiyo yekumusoro uriri). | |
| 3 | Shandura SW2 chinja kumusoro kana pasi kuti uchinje kukosha kwepasi kunoratidzwa. Dzvanya SW1 chinja pasi kwemasekonzi 1.5 kuti utange kudzidza kwepasi kubva pauriri hwekutanga. | Nguva yekutanga yaunodzidza, iwe unogona chete kutanga kubva pasi pasi kana pauriri hwepamusoro. Ndapota pedzisa kudzidza panguva imwe chete. |
| 4 | Kana iyo yekupinda munzvimbo yepasi yekudzidza mode yakabudirira, iyo-segment-segment code ichamira kupenya, uye nomwe-segment code uye IC icharatidza kutanga. Kana iyo yekupinda munzvimbo yepasi yekudzidza modhi ikatadza, E1 icharatidzwa. | |
| 5 | Mushandi ari mukati memotokari kana pamusoro pemotokari anozarura gonhi rekusimudzira, uye mufambisi ari mukati memotokari anoyera mutsauko wehurefu X pakati pepasi remukova sill uye sill yemotokari (kureba pamusoro pemotokari hakuna kunaka, uye kureba pasi pemotokari kwakanaka, chikwata chiri mm. Kana kuenzana kwekuenzanisa kunosangana nezvinodiwa [-3mm, 3mm], enda zvakananga kune danho rinotevera). | |
| 6 | Kana X iri kunze kwehuwandu hwe [-20, 20] mm, iyo yakaderera-speed operation mode inogamuchirwa kuti igadzirise kurongeka kwekuenzanisa kusvika mukati me [-20, 20] mm. | |
| 7 | Nzira yekushanda ye-low-speed operation mode ndeyokuti: kana X iri yakanaka, nzira yekushanda iri kumusoro, zvichida pasi. Mushure mekunge mushandisi ari mumotokari avhara gonhi resimudzi neruoko, anoramba achidzvanya bhatani rekuvhara gonhi pabhokisi rekudzora, uye ipapo anozivisa mutyairi ari pamusoro pemotokari nzira yekuvhiya uye kutanga zvinodiwa. Opareta ari pamusoro pemotokari anozoshandisa chigadziriso chekugadzirisa kuita kuti lifti imhanye. Elevator ichamhanya nekumhanya kwe2.1m/min. Panguva imwecheteyo, chiratidziro chiri mumotokari (IC) chinoratidza chinhambwe chafambwa neichi oparesheni (mu mm, museve wekumusoro unovhenekerwa nechakanaka, uye museve wepasi unovhenekerwa kune negative). Kana kukosha kunoratidzwa neIC kwakaenzana neX, mutyairi ari mumotokari anoburitsa bhatani rekuvhara gonhi pabhokisi rekutonga, uye lifti inomira kumhanya (slow stop). Mushure mekunge lifti yamira zvishoma nezvishoma, mushandisi ari pamusoro pemotokari anogona kukanzura mirairo yebasa rekugadzirisa. | |
| 8 | Kana X iri mukati meyero ye [-20, 20] mm, iyo yekupedzisira-yakaderera yekumhanyisa maitiro inogamuchirwa kuti igadzirise kurongeka kwakaringana kune huwandu hwe [-3, 3] mm. |
|
| 9 | Nzira yekushanda ye-ultra-low speed operation mode ndeyokuti: kana X iri yakanaka, nzira yekushanda iri kumusoro, zvichida pasi. Mushandi ari mumotokari anovhara gonhi rerevheti neruoko, obva aramba achidzvanya bhatani rekuvhura gonhi pabhokisi rekudzora, uye anobva azivisa mutyairi ari pamusoro pemota nzira yekuvhiya uye kutanga zvinodiwa. Opareta ari pamusoro pemotokari anozoshandisa chigadziriso chekugadzirisa kuita kuti lifti imhanye. Iyo elevator inomhanya nekumhanya kwe0.1m/min (kana iyo inoenderera yekushanda nguva ichipfuura 60s, software inomisa elevator). Panguva imwecheteyo, chiratidziro chiri mumotokari (IC) chinoratidza chinhambwe chafambwa neichi oparesheni (mu mm, museve wekumusoro unovhenekerwa nechakanaka, uye museve wepasi unovhenekerwa kune negative). Kana kukosha kunoratidzwa neIC kwakaenzana neX, anoshanda mumotokari anoburitsa bhatani rekuvhura gonhi, uye lifti inomira kumhanya (slow stop). Mushure mekunge lifti yamira zvishoma nezvishoma, mutyairi ari pamusoro pemotokari anodzima mirairo yebasa rekugadzirisa. | |
| 10 | Dzokorora matanho [5] kusvika [9] kusvikira kuenzana kwekuenzanisa kwagadziriswa kusvika mukati me [-3, 3] mm. | |
| 11 | Siya musuwo weelevator wakavhurika, anoshanda mumotokari odzvanya bhatani rekuvhura gonhi, obva adzvanya kaviri bhatani rekuvhara gonhi. Elevator icharekodha nzvimbo yepasi iripo. Kana kurekodha kwakabudirira, pasi rinoratidzwa richawedzera ne1 (kudzidza kubva pasi kusvika kumusoro) kana kuderera ne1 (kudzidza kubva kumusoro kusvika pasi). Kana ikatadza, E2 kana E5 icharatidzwa. | |
| 12 | Vhara musuwo weelevator, uye mushandisi ari pamusoro pemotokari anoshandisa chigadziriso chinomhanyisa chishandiso kuita kuti lifti imhanye nekumhanya kwekugadziridza kudzamara lifti yamhanyira kumusuwo weiyo uriri hunotevera kuti udzidzwe nekumira. | |
| 13 | Dzokorora nhanho [5] kusvika [12] kusvikira pasi rose radzidza zvinobudirira uye nomwe-chikamu kodhi uye IC icharatidza F. | |
| 14 | Mushandi ari mukamuri yemuchina kana ETP anodzvanya SW1 pasi uye SW2 kumusoro kwemasekonzi matatu, uye lifti inobuda pauriri chinzvimbo chekudzidza modhi. Kana kudzidza kwakabudirira, kodhi yezvikamu zvinomwe uye IC icharatidza FF. Kana kudzidza kwacho kuchitadza, kodhi yezvikamu zvinomwe uye IC icharatidza E3 kana E4. | |
| 15 | Seta SET1/0 kusvika 0/8 wodzvanya SW1 chinja pasi. | |
| 16 | Gadzirisa P1 bhodhi kana kudzima elevator wobva waibatidza zvakare. | Usazvipotsa! |
Zvinorehwa nemakiyi manomwe-segment macode kana IC maratidziro anoratidzwa mune inotevera tafura:
| Tafura 9 Zvinoreva kodhi yezvikamu zvinomwe | |
| Seven-segment kodhi kana IC kuratidza | Kureva |
| E1 | Yatadza kuisa layer mode |
| E2 | Tatadza kurekodha ruzivo rwenzvimbo yepasi |
| E3 | Yatadza kubuda kunyora layer mode |
| E4 | ZFS-ELE200 yakundikana kunyora ruzivo rwenzvimbo |
| E5 | Iyo data yenzvimbo yepasi haina musoro |
| F | Ese pasi munzira yekudzidza (kumusoro kana pasi) akadzidzwa zvinobudirira |
| FF | Nyora pasi data zvakabudirira |